Tag: homestead

Frequently Asked Questions About Tapping Maple Trees

We hear a lot of questions about how to tap trees, collect maple sap and make maple syrup. Today we will talk about some of the most frequently asked questions we see and answer them below. If you have a question you’d like us to answer, ask us in the comments below or connect with us over on Facebook!

What is the smallest tree I can tap?

The smallest tree you would want to tap would have a diameter of 10” or ten inches. Trees smaller than that should not be tapped.

Can I install more than one tap or spout in my maple tree?

Trees with a diameter of 10”to 17” can support one tap. Trees with a diameter of at least 18” can support two taps.

How much sap will I get from each maple tree?

Each tree should produce around ten to twenty gallons of sap each season. This varies depending upon the maple season and the health of the individual tree. For example, two identical trees located right next to each other can produce very different levels of sap.

How deep should I drill into the tree?

Drill into the tree approximately 1.5” past the bark and into the white wood. Total depth is approximately 2.5”.

Does maple tapping hurt or damage the tree?

Tapping does not hurt or damage the tree. Following proper care when tapping will avoid any damage to the tree. Only drill one tap hole with one spout for small trees to reduce stress on the tree. The maple is the only species that is self-healing, and the tap hole will heal and close up during the year.

When I’m done collecting sap, should I put anything into the tap hole to stop the flow of sap?

No. The maple tree will heal and close up the tap hole on its own. Never put any foreign objects or plugs into the maple tree.

What is in maple sap?

Maple sap is a complex natural blend of water, sugar, minerals, vitamins and antioxidants.

Is it safe to drink sap straight from the tree?

Generally speaking, sap is sterile before it leaves the maple tree. However, bacteria can enter the sap once it leaves the tree and is exposed to the environment or your collection container. It is similar to consuming raw cow’s milk; there are both risks and benefits to consuming raw vs. pasteurized beverages. To be safe, boil your maple sap first before drinking it.

How much sap does it take to make a gallon of finished maple syrup?

Sugar maples have the highest concentration of sugar in their sap, so they work best for making syrup. It takes about 40 gallons of sap boiled down to make one gallon of finished syrup.

Where can I buy a maple tree tapping kit and supplies?

Buy a complete tree tapping kit complete with guide sheet and instructions here at our online shop.

How do I tap a maple tree?

Watch our video guide on how to make maple syrup here!

How do I identify what kind of maple trees I have?

See our complete guide on identifying maple trees here.

How to Make Maple Syrup

Learn how to tap your maple tree, collect the sap and boil it down into syrup! We just tapped our trees a few days ago here in Connecticut, and have already collected several gallons of fresh, nutrient-rich organic maple sap. We boiled down the sap with a propane gas burner until the sap reached a wonderful golden amber color and stored it in a sterilized mason jar.

This buttery, light amber syrup pictured above is characteristic of the syrup produced very early in the sugaring season. As the season progresses, the syrup produced will become slightly darker in a medium amber color, eventually getting very dark and robust in flavor as we near the end of the season.

How to Tap a Maple Tree

After properly identifying your maple trees, you are now ready to begin tapping!

  1. Gather the tools for the job: drill (cordless preferred), hammer, food grade collection container, and a 5/16” drill bit.
  2. Locate the tree’s Southern exposure. The side facing South tends to produce sap earlier than other sides of the trees.
  3. Measure the height of the tap hole carefully before drilling. The tap height is based on the total height of your collection container and the length of tubing. Be careful not to drill too high up.
  4. Drill into the tree approximately 1” past the bark, into the white wood, at a very slight upward angle. Remember to use caution and wear eye protection while drilling.
  5. Insert the smooth end of the spout into the tree, while the barbed end inserts into your blue tubing. (Pro Tip: place the end of the tubing into hot water for 10 seconds to ease the attachment of the tube to the spout!)
  6. Firmly tap the spout into the tree, and be careful not to hammer the spout in too much or it will be difficult to remove. It’s better to have the spout slightly loose than to have it stuck in the tree.
  7. Connect your tubing to a food grade collection container. We suggest using a large, clean spring water jug or soda bottle. Be sure to check the collection container daily, up to twice a day (morning and night) as the flow of sap varies by tree and temperature.
  8. When you’re finished collection, the equipment can be cleaned and reused next year. (Pro Tip: to ease disassembly of the tube and spout, place in hot water again for 10 seconds to soften the tube.

Get your maple tree tapping kit here on Amazon. Need some more help? Chat with us here on Instagram.

The clear blue tubing enhances visibility in the woods so you know exactly where your tapped trees are, even after an early Spring snow storm! There is nothing better than making 100% pure organic maple syrup yourself with these simple tools at home.

Maple tapping season runs from January through April, and varies by region. Birch sap flow begins when maple season ends. The season’s length also varies by earth climate patterns year to year. Please research the season in your region before ordering, or send us a message and we’ll be happy to help.